Ikelite Fiber Optic Converter for DS Strobes (3rd Gen)
Ikelite Fiber Optic Converter for DS Strobes (3rd Gen)
Ikelite Fiber Optic Converter for DS Strobes (3rd Gen)
Mfr# 4401.3
Our Price: $119.95
Availability: In Stock
Qty:  
   - OR -   

Converts the electrical bulkhead of any Ikelite DS strobe into a fiber optic port.

This 3rd Generation of the Fiber Optic Converter features a hard anodized aluminum plug connection which reduces weight without sacrificing durability. It is recommended for use with any Ikelite strobe produced September 2018 or later with a hard anodized aluminum bulkhead.

Like the 2nd Generation model, this Fiber Optic Converter features heightened sensitivity for use with SEA&SEA or Nauticam housings with internal electrical-to-optical flash triggering devices. These devices translate the camera's electrical signals into a series of LED flashes which are much less bright than a traditional built-in camera flash. The Fiber Optic Converter is also compatible with any system where the camera's built-in flash can be seen by a fiber optic cord.

Attachment and Use

The Converter simply attaches to the strobe's electrical bulkhead in place of a sync cord connector. The enlarged slave window provides approximately 90 degrees field of view for remote triggering. 

The Fiber Optic Converter automatically configures itself for compatibility with both pre-flash and non pre-flash camera modes. No setting of small switches or confusion over number of pre-flashes. Simply turn on your strobe and take one picture to configure. This adapter is a manual exposure (non-TTL) trigger only. The strobe's output may be adjusted using the manual power settings built into the strobe (varies by model). 

An individual Fiber Optic Converter and compatible cord is needed for each strobe. Use of two strobes requires two Fiber Optic Converters.

This converter attaches to an Ikelite DS strobe. It is not intended to be attached to a housing and will provide no functionality if attached to an Ikelite bulkhead in a housing.

Alternatives

There are two shooting scenarios where the High Sensitivity Optical Slave Converter # 4405 would be a better option:

  • If you're shooting a DSLR or mirrorless camera with Nauticam fiber optic converter and want to shoot at a higher frame rate (4 FPS or faster).
  • If your primary purpose is to trigger your strobes remotely at a distance from the housing without a fiber optic cable in between.

Strobe Compatibility

  • Ikelite DS50, DS51
  • Ikelite DS125
  • Ikelite DS160, DS161

Fiber Optic Cord Compatibility

  • Ikelite Fiber Optic Coiled Cord # 4501
  • INON Optical D Cable "Non-wireless type" L-Connector
  • SEA&SEA Fiber Optic Cable (L-type) # 50107
  • SEA&SEA Fiber Optic Cable II # 50128
  • Olympus UW Fiber Optic Cable PTCB-E02
  • Nauticam Optical Fiber Cable # 26211 Nauticam to INON
  • Nauticam Optical Fiber Cable # 26212 Nauticam to Sea&Sea

Function / Efficiency
Depth rating 90m / 300 ft.
Compatibility
Strobes Ikelite DS50, DS51, DS125, DS160, DS161, DS200 Strobes
Basic
Dimensions 1.1 x 2.7 in / 28 x 69mm
Weight 1.6 oz / 45g
Materials Plastic, Stainless steel.
Warranty 1 Year
  • Fiber optic adapter
  • Connector protector
  • Silicone grease
  • User manual
  • 1 Year warranty

 

SSL Certificate EV SSL
Copyright © 2013 DiverVision U/W Photo Equipment All Rights Reserved